-To insert, slide the ION Power Pack Battery into the slot on the back of the handheld vacuum. -To remove, pinch the release tab and slide the ION Power Pack battery out of the handheld vacuum.
-The lights on the ION Power Pack serve multiple purposes. One purpose is to show the remaining charge in your ION Power Pack while in use. The lights will also blink and illuminate to show the status of the ION Power Pack while charging. In addition, the lights will illuminate in certain configurations to inform you of any issues with the ION Power Pack.
-You can charge your ION Power Pack by using a Shark ION Power Pack Charger along with accessories such as the charging dock and wall mount. Please note that only Shark chargers should be used to charge an ION Power Pack. Consult your instruction book for approved models.
A single power pack runtime is approximately 23 minutes with new battery on extended runtime in handvac mode. You can benefit from hassle-free cleanability by swapping out with a second battery which will give you over 40 minutes of cleaning in extended runtime mode - more than the Dyson V8 Absolute! If customer requests specific run times for the different modes: -The ION Power Pack, like all lithium-ion products, will naturally decrease in capacity over time from the 100% capacity of a new battery. -These times are based on 100% capacity. Mode - Expected Run Time: -Handvac Only Max Power - approx. 11 min. -Handvac Only Extend Runtime - approx. 23 min. -Floor Mode Max Power - approx. 12 min. -Floor Mode Extend Runtime - approx. 20 min. -Carpet Mode Max Power - approx. 11 min. -Carpet Mode Extend Runtime - approx. 14 min.
-The initial charge on the pack is approximately 30%. Fully charge the pack " 3.5 hours minimum / overnight preferred " and assess battery performance. - Note that battery run time is affected by the amount of work you are performing. Vacuuming on high pile carpet while using Max Power will reduce battery run time quicker than vacuuming bare floors. - If you have more than one battery, it is recommended that you use each equally in use and charging.
-Your ION Power Pack may feel warm in use as air passes through the vacuum. If it feels uncomfortably warm, stop using the vacuum and allow for the battery to cool. If the battery continues to feel warm, or you see any LED indicators as outlined in your instruction book, contact Customer Service. -The charger is designed to monitor many factors of the battery. After use, batteries can get warm a condition that is not optimal for charging. In such cases, the charger waits for the battery temperature to decrease to the optimal point before it begins charging.
The Shark ION Rocket Cord-Free vacuum has two floor settings for cleaning " a Bare floor, Area Rug Setting and a High Pile Carpet Setting. Note that the headlights will illuminate any time the power is on and the brushroll is spinning. (Note: No headlights on IR70) It also has two power settings: Extend Runtime and Max Power. Use Extend Runtime for your everyday cleaning and switch to Max Power if you need a bit more suction for a small spill.
To turn the vacuum off, press the power button.
Step on the "Wand Release" foot pedal on the floor nozzle and pull the wand off. Attach desired accessory to the end of the wand and begin cleaning
This vacuum has convenient storage with its built-in storage hook. Simply remove the handvac from the wand by pressing the wand release button and place the handvac on the storage hook. The handvac has a catch on the side of the dust cup. The hook is located above the nozzle. Another option is to simply lay the vacuum flat on the floor. There are rubber pads on the base of the handheld vacuum that prevent scratching.
First, turn off the power and remove the battery. Then, separate the handheld from the rest of the vacuum by pressing the "Wand Release" button. Next, hold the dust cup over the trash and press the "Empty" button. Tap gently to empty contents and pull any debris off of the metal screen. If desired, wipe clean with a dry soft cloth. Close the lid. You will hear it click into place. For optimal performance, the dust cup should be emptied each time you vacuum and when the dust cup appears full or debris reaches the "MAX FILL" line.
For optimal performance, the dust cup should be emptied each time you vacuum and when the dust cup appears full or debris reaches the "MAX FILL" line.
For optimal performance, clean filters on a regular basis. Between washings, your filter can be tapped clean to remove any excess dust and other particles into the trash. -Pre-Motor Foam and Felt Filters: Under normal usage, rinse and let air dry completely (for at least 24 hours) once a month. -Post-Motor Filter: Under normal usage, rinse and air dry once every 9 months or as needed.
The pre-motor filters are located on the top of the handvac. Turn off the power and remove battery. Place the rest of the vacuum on the floor. Pull out the filter assembly. Gently separate the cylindrical foam filter from the felt. Rinse both filters with water until the water runs clear. DO NOT use soap. Let air dry completely (at least 24 hours) before reinstalling. Slide the foam filter back onto the felt filter and reinstall. The post-motor filter is located under the handle of the vacuum. Press the button to remove the cover and pull out this filter. Rinse with water until the water runs clear. DO NOT use soap. Let air dry completely (at least 24 hours) before reinstalling. Reinstall the filter under the handle and press the cover closed until it clicks into place.
1. Make sure the nozzle is flat against the floor and the vacuum is tilted back out of upright lock. 2. Make sure the power switch is on. 3. If red light is illuminated on the floor nozzle, check for blockages (refer to Instruction Booklet). 4. Turn power off and remove battery. Then, remove any excess hair that has wrapped around the brushroll. Avoid damaging or cutting the bristles. 5. Check that the handheld vacuum and wand connectors are fully engaged and are making an electrical connection with the floor nozzle. If the brushroll is still not turning on, please contact Customer Service at 1-800-798-7398. Make sure the nozzle is flat against the floor and the vacuum is tilted back out of upright lock. 2. Make sure the power switch is on. 3. If red light is illuminated on the floor nozzle, check for blockages (refer to Instruction Booklet). 4. Turn power off and remove battery. Then, remove any excess hair that has wrapped around the brushroll. Avoid damaging or cutting the bristles. 5. Check that the handheld vacuum and wand connectors are fully engaged and are making an electrical connection with the floor nozzle. If the brushroll is still not turning on, please contact Customer Service at 1-800-798-7398.
First, make sure the vacuum is turned off. Then, turn the vacuum back on and tilt the vacuum back while gently stepping on the floor nozzle. Note that when you lock the vacuum in the upright position, the brushroll will stop spinning after a few seconds. If the brushroll is still not spinning, check for blockages in the brushroll. Then repeat the steps above. If the brushroll is still not spinning, please contact Customer Service at 1-800-798-7398.
Certain dry temperatures in winter or dry desert areas may cause common static electricity to build up in the vacuum and produce small shocks, similar to what you might experience from door knobs, wool sweaters or blankets. This is harmless. In order to avoid this, we recommend moisturizing your hands and/or removing wool socks or sweaters prior to vacuuming.
It is possible that the vacuum has overheated. It is equipped with a motor protective thermostat. To reset it, turn the power off and remove the battery. Check for clogs or dirty filters. Clear any clogs and wash filters as is necessary (refer to Instruction Booklet). Wait a minimum of 45 minutes for the vacuum to cool. Then reinsert battery and turn the power on. If the vacuum still does not start, please contact Customer Service at 1-800-798-7398.
The LED lights in the nozzle should not burn out if the vacuum is functioning as it should. If you don"t see your question here, please refer to the Instruction Booklet or contact Customer Service at 1-800-798-7398.
- Pre-motor filters are located in a separate compartment in the dust cup - Pre-motor filters are a different design - Dust cup capacity is lower to the max fill line " equals HV300 capacity -There is no LED Accessories with electrical connections are not compatible (Deep-Cleaning Motorized Pet Tool) Pre-motor filters are located in a separate compartment in the dust cup - Pre-motor filters are a different design - Dust cup capacity is lower to the max fill line " equals HV300 capacity -There is no LED Accessories with electrical connections are not compatible (Deep-Cleaning Motorized Pet Tool)
Check to see if the filters need to be cleaned if the vacuum is not picking up dirt, airflow is restricted, or if you notice lighter or no suction. You can tap loose dirt off filters between washes and wash them according to the regular cleaning schedule to maintain optimal performance. Refer to Instruction Booklet for more information.
1. Turn off the power and remove battery. 2. Check for blockages along the airflow path. 3. Check accessories and clear blockages if necessary. 4. Empty the dust cup and clean the filters. Refer to Instruction Booklet for more information. Turn off the power and remove battery. 2. Check for blockages along the airflow path. 3. Check accessories and clear blockages if necessary. 4. Empty the dust cup and clean the filters. Refer to Instruction Booklet for more information.
1. Remove the wand and inspect all handheld vacuum openings to make sure there are no obstructions. 2. Remove the floor nozzle from the wand and check for blockages. 3. Inspect the inside of the wand, specifically the flap near the hose, and clear any blockages. 4. Check that there are no blockages in the air path and no excess hair or fibers around the brushroll.
The model number is displayed on the vacuum"s rating label, which can be found on the handheld portion of the vacuum behind the dust cup.
There are 3 ways to register your vacuum. On the web go to registeryourshark.com, call 1-800-798-7398, or scan the QR code using a mobile device.
The QR code is an easy way to register your vacuum.
The QR code is displayed on the handheld portion of the vacuum behind the dust cup and on the inside cover of the instruction booklet.
Depending on the mobile device you have, please reference their instructions on how to use their QR code scanner.
A wide assortment of accessories are available for use with the Shark ION Rocket Cord-Free Ultra-Light. Some of these accessories maybe included with the specific vacuum you purchased. Please reference the list in your Quick Start Guide. All of the accessories listed below are compatible with your Shark ION Rocket and available for purchase on SharkAccessories.com -5" Crevice Tool -12" Crevice Tool -18" Flexi Crevice Tool -Duster Crevice Tool -Dusting Brush -Pet Multi-Tool -Multi-Angle Dusting Brush -Anti-Allergen Dust Brush -Wide Pet/Upholstery Tool -Pet/Upholstery Tool -Deep-Cleaning Motorized Pet Tool -Home & Car Detail Kit -Precision Duster -MultiFLEX Under Appliance Wand -Large Accessory Bag (fits MultiFLEX Under Appliance Wand) -Small Accessory Bag -Deep cleaning MPT Tool Clip
There are two ways to clean with the accessories. Either separate the handheld portion from the rest of the vacuum by pressing the "Wand Release" button or keep the wand connected to the handheld and remove the floor nozzle by stepping on the foot pedal release. Choose the desired cleaning accessory and slide it onto the end of the handheld vacuum or the end of the wand. Note that the accessories do not need to be pushed all the way onto the vacuum to be secure. Only the Deep-Cleaning Motorized Pet Tool clicks into place. Also note that the wand can bend for more flexible reach by using the MultiFLEX feature.
-5" Crevice Tool: access to tight, narrow spaces -12" Crevice Tool: access to tight, narrow spaces -18" Flexi Crevice Tool: rubber extension flexes for access to tight, narrow spaces -Duster Crevice Tool: combination dusting brush and crevice tool, soft bristles great for dusting delicate surfaces, bristle head is removable for longer reach -Dusting Brush: clean large or small debris and dust, bristle head turns to adjust to your cleaning surface -Pet Multi-Tool: 2-in-1 combination tool designed to dust a multitude of surfaces, pick up large piles of debris and remove pet hair from curtains and other delicate fabrics -Multi-Angle Dusting Brush: 5-position soft dusting brush for cleaning shelves, blinds, walls, ceiling fans and lights; adjust the angle to the desired cleaning surface -Anti-Allergen Dust Brush: fine dusting of knick-knacks and delicate objects, in between narrow spaces -Wide Pet/Upholstery Tool: extra wide accessory removes pet hair and dust from curtains, mattresses and other delicate fabrics -Pet/Upholstery Tool: picks up pet hair and large piles of debris from upholstery and other fabrics -Deep-Cleaning Motorized Pet Tool: powered by a motor to remove pet hair and embedded dirt from carpeted stairs, upholstery, tabletops, bookshelves, and car interiors -Home & Car Detail Kit: assortment of micro tools designed to clean keyboards, car interiors and around delicate objects -Precision Duster: flexible tube with micro duster crevice tool for cleaning keyboards, car interiors and around delicate objects -MultiFLEX Under Appliance Wand: adjustable accessory for cleaning under and behind hard to move appliances and furniture -Large Accessory Bag: store accessories, 12.5" x 27.5", fits MultiFLEX Under Appliance Wand-Small Accessory Bag: store accessories, 12.5" x 18" -Flexible Hose: extension hose for more flexibility to clean hard to reach areas in and around objects and furniture -Deep-Cleaning MPT Tool Clip: removable accessories clip attaches to the wand, can store up to 2 accessories including the Deep-Cleaning Motorized Pet Tool (on the top post)
You can purchase replacement parts and other accessories through SharkNinja® Customer Service at 1-800-798-7398 or on SharkAccessories.com.
The Shark ION Rocket Cord-Free is available through Sharkclean.com, Customer Service at 1-800-798-7398, or at any one of our retail partners across the U.S.
7.2 lbs. (no accessories)
11.9" L X 10.3" W X 45.6" H
The dust cup holds 0.3 dry quarts up to the MAX fill line.
The Shark ION Rocket Cord-Free is produced with a combination of durable ABS and PP plastics, along with some metal and rubber components.
Parts include the handheld vacuum, motorized floor nozzle, and wand. It also comes with a variety of cleaning accessories. Depending on the version you purchased, these accessories will vary slightly. To find out specifically what is in your version, consult the Quick Start Guide that came with your unit.
It is available in Charcoal Grey with silver (IR100) or fuchsia (IR101) accents. It also comes in Forest Mist (IR70).
The Shark ION Rocket Cord-Free Ultra-Light is manufactured by our high-quality vacuum manufacturing partners in China.
-The ION Power Pack is a 25.2 volt removable, rechargeable lithium-ion battery pack.
The ION Power Pack, like all lithium-ion products, will naturally decrease in capacity over time from the 100% capacity of a new battery. Your purchase is recorded upon product registration. Our Customer Care agents can review to determine whether your battery is under warranty.
0.3 dry quarts to the MAX FILL line